The nights are long now, and your windows spend every one of them giving away heat you paid for. That's where this winter's heating bill starts.

Black Friday lands on the 27th, so today also covers one thing to check before you say yes at checkout.

Below: curtains that hold heat, a longer pair worth a look, the ceiling fan's winter switch, the dryer's sensor bars, and the warranty math before Black Friday.

Reply and tell us: which room in your house feels coldest at night? We read every one.

Why Your Curtains Stop Just 10% of Heat Loss

Hand-drawn guide to curtains that hold heat: close the top, seal the sides, overlap 4 inches and reach the sill or floor; open south windows in sun, close them all at night. Usual hang up to 10%, sealed hang up to 25%.

Image: The Home Wire

Ordinary curtains, hung the usual way, cut the heat your windows lose by 10% at most. Hang the same drapes sealed and that climbs to up to 25%, per a Cornell Cooperative Extension fact sheet.

That's the job for this week, while the first long cold nights settle in and your windows give up heat until morning.

The usual way fails at the top. Warm room air slides in behind the curtain, cools against the glass, drops, and rolls out the bottom into the room. Your curtain becomes a chute. Cornell calls it the "tunnel" effect, and a closed top stops it.

Cornell's numbers come from older tests on single-pane windows, so treat them as a rough guide. The Department of Energy lands in the same place. Its March 2024 bulletin says most average draperies cut window heat loss by up to 10%, while tightly installed cellular shades cut it by about 40%.

Blinds are the weak spot. Vinyl or metal blinds cover about 60% of US windows, and a DOE fact sheet says they "do not provide much insulation." In a DOE test house in Knoxville, cellular shades saved up to 20% on heating energy compared with bare windows.

Here's the routine, tonight and every night:

  1. Close every curtain, shade and blind at dusk.

  2. Open the south-facing ones on sunny mornings so the sun can heat the room.

  3. Let your drapes reach the sill or the floor.

  4. Overlap the two panels about 4 inches in the middle.

  5. Close the top with a valance or cornice, or mount the rod close to the wall and frame.

  6. Pull the side edges back to the wall or the window frame.

Step 5 is the easy one to miss. A rod that sits a few inches off the wall leaves the top open, and that gap is where the tunnel starts.

Renting? Curtains and rods are all yours. Use a tension rod or the rod you already have, and ask before you drill.

If your drapes stop short of the sill, the fix is a longer pair. Scroll down for one that reaches.

Worth a Look

Floor-Length Curtains That Close the Gap

If your bedroom curtains stop a few inches short of the sill, the NICETOWN Thermal Insulated Blackout Curtains are the easy swap worth a look. At 84 inches long, they reach the sill or the floor on most standard windows, and that's where the curtain math above starts to work.

You get two panels, each 52 inches wide. Each one has both a back-loop top and a rod-pocket top. Either way, they sit tighter to the rod than grommets do, which helps you close the top.

Before you order, check the width. For that 4-inch overlap in the middle, the two panels together should be wider than your window.

The fabric is a triple weave that blocks 85% to 99% of light and UV. There's no separate lining, though, and the promise that it keeps out winter chill is the maker's own claim, not an independent test. Think of them as the right length and the right fit first, and the insulation as a bonus.

The pair is $19.99 at time of writing. We haven't hung these ourselves; the specs come from the Amazon listing, and we read the price there on Sunday, Nov. 15.

Renting? They slide onto the rod you already have, no drilling. Here's the pair on Amazon.

Links in this post may be affiliate links. The Home Wire may earn a small commission if you buy through them, at no extra cost to you.

Flip Your Ceiling Fan to Winter Mode

A hand reaching up to the small direction switch on the motor housing of a white ceiling fan in a warmly lit living room in winter.

Image: The Home Wire

Your ceiling fan has a winter setting: low speed, clockwise. ENERGY STAR says that makes a gentle updraft, which forces the warm air near the ceiling down into the part of the room you actually use.

Clockwise means the blades move left to right when you stand under the fan and look up. If you set it for summer and never touched it again, it's still spinning the other way.

The switch is usually on the fan's housing or the light fixture, says Hunter. On many remote models there's no switch to hunt for. Hunter's support page says to press and hold the fan button on the remote or wall control, and the light blinks to confirm.

One rule before you reach up: let the fan stop completely before you change direction.

Here's the routine:

  1. Turn the fan off and let it stop.

  2. Find the direction switch on the housing, or press and hold the fan button on your remote.

  3. Flip it.

  4. Run the fan on low.

  5. Stand under it and check that the blades move left to right.

  6. Turn it off when you leave the room.

That last step is ENERGY STAR's advice too. The fan is there to push warm air down on you, so it can rest when nobody's under it.

Renting? This one is all yours. No tools, no call to the landlord.

The Dryer Strip That Ends Cycles Too Soon

A hand wiping a curved metal strip inside an open clothes dryer drum with a soft damp cloth.

Image: The Home Wire

If your Sensor Dry loads keep coming out damp, the fix is probably a wipe of the moisture bars inside the drum. Dryer sheets leave a film on them, and the dryer stops reading the load.

Here's how it works. Sensor Dry uses bars inside the drum to detect moisture, and it ends the cycle once it can't find any more, according to Samsung. Frequent dryer sheets leave residue on those bars. Coated bars can't pick up the water, so the dryer thinks the load is dry and quits early.

That costs you twice. A cycle that quits early means a second run. And a sensor that can't sense can't save. ENERGY STAR says certified dryers save energy by using automatic termination to detect when clothes are dry, and LG says sensor dry helps reduce energy use.

Here's the routine:

  1. Unplug the dryer or turn it off.

  2. Open the door and find the bars. They're usually metal strips on the inside of the drum, often near the lint filter. Check your manual if you don't spot them.

  3. Wipe the bars with a soft cloth and mild soapy water.

  4. Dry them with a towel.

  5. Clean the lint filter while you're there. ENERGY STAR says to do that after every load.

How often? Samsung says to clean the bars whenever Sensor Dry cycles start running short. LG says regular cleaning keeps the sensor from getting contaminated.

One check before you blame the bars. A very small load can stop after about 10 minutes, and LG says that's normal.

Renting with in-unit laundry? This one's all yours. On a shared machine, tell your landlord.

Before Black Friday, Do the Warranty Math

Most extended warranties cost about what the repair would. So before you click yes at checkout on Black Friday, Friday, Nov. 27, check what you're already covered for.

The numbers are thin. A 2018 Consumer Reports analysis found extended warranties cost an average of $126 for large appliances and $21 for small ones. Repairing without a plan cost just $26 more on average.

Laptops tell the same story. In a 2019 Consumer Reports look at laptop coverage, only 15% of PC owners who bought extra coverage used it for repairs. Among Apple owners, it was 7%.

The FTC says a plan isn't a good value if it doesn't cover more than the warranty that came with the product. It's only as good as the company responsible for the coverage. And its blunt rule: "If it isn't listed in the contract, assume that it's not covered."

You may already have more than you think. Some credit cards stretch the maker's warranty. One example: eligible American Express cards add up to 1 more year on warranties of 5 years or less. Terms vary by card, so check yours.

Here's the check before you pay for a plan:

  1. Read what the included warranty already covers.

  2. Look up your card's benefit guide for extended warranty coverage.

  3. Ask who backs the plan.

  4. Find any deductible or fee you'd pay each time it's serviced.

  5. Divide the price by the years it covers to get the yearly cost.

Then weigh it. If the product isn't likely to need repairs, the FTC says the plan might not be worth it, and putting that money aside in savings may be the better move.

One quick tap

That's Tuesday: curtains that hold heat, a longer pair, the ceiling fan's winter switch, the dryer's sensor bars and the warranty math.

If you only do one thing this week, close every curtain at dusk tonight.

Forward this to whoever in your house is always cold by the window.

See you tomorrow.

The Home Wire

This post may contain affiliate links. The Home Wire may earn a commission if you purchase through our links, at no extra cost to you. We only recommend products we believe earn their place in your home.

30 N. Gould St. Suite R Sheridan, WY 82801, United States